Research and design of internal meshing gear pump separating crescent plate | Scientific Reports

Scientific Reports volume 14, Article number: 3519 (2024) Cite this article

868 Accesses

1 Citations

Metrics details

The design of the crescent block is a key factor in the high-pressure operation of the internal meshing gear pump. In order to increase the output pressure of the pump, this article designs a new type of separable crescent plate. Then, taking a certain type of high-pressure internal meshing gear pump as the research object, a nonlinear differential equation for the internal flow field of the gear pump was established, and the pressure distribution law in the transition zone of a cycle was derived. A mathematical model of the device was established based on the equilibrium conditions of the internal and external crescent block forces. Finally, experimental research was conducted on the design parameters of the separation crescent plate. The results showed that under the conditions of displacement of 100.5 ml/r, pressure of 20.5 MPa, and rotational speed of 1800 RPM, the compensation chamber angle range was 31.23°, and the pump's volumetric efficiency could reach 94.6%. There were no abnormal phenomena during the entire operation of the pump, and there was no jamming or jamming of the friction pair.

Internal gear pumps have the characteristics of compact structure, small volume, low noise, and low flow pulsation, and are widely used in industrial equipment1. Due to its good suction performance, high energy density, and high conversion efficiency, it is more suitable for hydraulic circuits such as power systems, steering systems, and transmission systems. Due to the existence of radial imbalance force2, internal gear pumps are constrained in terms of pressure increase, and there is still a gap in pressure compared to plunger pumps. Therefore, the development and design of high-pressure internal gear pumps are still an important research direction in the current gear pump field3.

In order to further improve the pressure of internal meshing gear pumps, mainstream scholars have proposed two ideas4. One is dedicated to the study of how to directly reduce radial imbalance force, typical work can be seen in references5,6,7, and the other is to design a static pressure compensation groove structure to offset radial imbalance force, detailed reference can be made in references8,9,10. Because the radial imbalance forces of these two approaches cannot be completely eliminated, they are often combined with static pressure compensation structures. The compensation device designed according to this method has a crescent-shaped external structure, called a crescent block. Due to the influence of multiple complex dynamic pressures in the transition zone11, it is difficult to establish an accurate mathematical model. References9,12,13 conducted simulation research on the pressure distribution flow field on its outer surface, while references11,14,15 conducted experimental research on the lubrication performance of the static pressure device. However, these studies do not provide strong guidance for engineering design.

Based on these reasons, this article proposes a separated crescent block structure suitable for high-pressure internal meshing gear pumps. Then, taking this structure as the research object, numerical calculation methods and theoretical research methods suitable for solving unbalanced radial force under high-pressure working conditions of internal meshing gear pumps were explored to study the pressure distribution law in the transition zone. Combined with the compensation effect of static pressure support on unbalanced radial force, the influence of the position and structural size of static pressure support groove on the compensation effect of unbalanced radial force was analyzed. Finally, Further determine the separated crescent block structure that meets the requirements for unbalanced radial force. Meanwhile, this article conducts a series of experimental studies on the design and operation of high-pressure internal meshing gear pumps to verify the reliability of numerical calculation methods. Therefore, the actual goal of this work is to deeply study the calculation model of the radial compensation mechanism of the internal meshing gear pump.

The compensation mechanism for radial clearance of internal meshing gear pump is shown in Fig. 1.The outer gear 1 and inner gear 2 rotate counterclockwise. An oil suction cavity \({{\text{P}}}_{0}\) is formed on the lower side of the central axis, and an oil discharge cavity \({{\text{P}}}_{{\varvec{h}}}\) is formed on the upper side of the central axis. The high and low pressure areas are separated by isolation devices16. The isolation device consists of a stationary stop pin 10, a floating outer crescent block 9, and an inner crescent block 3. The outer surface of outer crescent block 9 fits with the tooth top circle of inner gear 2, while the inner surface of inner crescent block 2 fits with the tooth top circle of outer gear 117. The first baffle spring 5, first sealing rod 6, second baffle spring 7, and second sealing rod 8 are arranged between the outer crescent block and the inner crescent block, forming zones I, II, and III18. Introduce the high-pressure \({{\text{P}}}_{{\varvec{h}}}\) of the oil discharge chamber into Zone I through the rectangular pressure spring 4.The transition pressure from \({{\text{P}}}_{{\varvec{h}}}\) to \({{\text{P}}}_{0}\) is distributed on the outer surface of the isolation device. By reasonably arranging the positions of the first baffle spring 5, first sealing rod 6, second baffle spring 7, second sealing rod 8, and rectangular compression spring 4, the crescent block has compensation in the diameter direction, which can compensate for surface wear between the isolation device and the gear pair19. It can be thus obvious that the key to increasing the pressure of the internal meshing gear pump is to achieve the balance of the compensation device under high pressure. It is necessary to prevent the increase of leakage caused by insufficient balance and the decrease of volumetric efficiency, as well as to prevent excessive balance from damaging the oil film layer and causing wear and burn20.

Schematic diagram of radial compensation mechanism for internal meshing gear pump: (A) Schematic diagram; (B) Partial enlarged view. (1, External gear; 2, Internal gear; 3, Stop pin; 4, The inner layer of a crescent-shaped isolation plate; 5,The outer layer of the crescent-shaped isolation plate; 6, First sealing rolle; 7, First pressure plate spring; 8, Second sealing roller; 9, Second pressure plate spring; 10, Third pressure plate spring; 11, Expanding the oil chamber).

The pressure in the transition zone consists of three parts: the high-pressure zone, the tooth tip clearance zone and the tooth concave zone. After adopting the technology of expanding the high-pressure area, the tooth concave area only has one tooth concave range. The pressure \({p}_{2}\) variation of the tooth concave depends on the flow difference between the radial clearance \({h}_{i}\) and the axial clearance \({h}_{f}\) per unit time21. During the working process, the radial clearance \({h}_{i}\) and axial clearance \({h}_{f}\) are both very small, and the working oil has a certain viscosity.22 Therefore, clearance flow can be considered as laminar motion. The leakage amount of the clearance can be calculated based on theoretical pressure difference shear flow model for clearance flow between two parallel plates23,24.

Establish a geometric model of the tooth concave area, as shown in Fig. 2. The radial clearance leakage flow consists of two parts: the leakage flow \({q}_{1}\) from the high-pressure area to the tooth concave area and the leakage flow \({q}_{2}\) from the tooth concave area to the low-pressure area.The axial clearance leakage flow consists of three parts: the leakage flow \({q}_{3}\) flowing from the high-pressure area on both sides of the gear teeth to the concave area, the leakage flow \({q}_{4}\) flowing from the concave area to the low-pressure area, and the leakage flow \({q}_{5}\) flowing from the concave area to the bearing cavity along both sides of the tooth root.

Geometric model and fluid dynamics model of the tooth concave area.

Based on the structural analysis between the gear and the crescent block and the side plate25, a pressure difference shear flow model was used to calculate the radial leakage flow \({q}_{1}\) and \({q}_{2}\) of the gear pump, as well as the axial clearance leakage flow \({q}_{3}\), \({q}_{4}\) and \({q}_{5}\), as follows26:

In the equation, \(\mu\) is the dynamic viscosity of hydraulic oil, \(b\) is the width of the gear, \({\text{s}}_{e2}\) is the tooth tip thickness of the internal gear, \({\text{s}}_{2}\) is the width of the internal gear indexing circle, \(p_{g}\) is the end pressure of the high-pressure oil tank, \(p_{2}\) is the pressure in the transition zone, \(p_{0}\) is the low-pressure chamber pressure, \(R_{e2}\) is the radius of the top circle of the internal gear teeth, \(R_{i2}\) is the radius of the inner gear root circle, \(u_{02}\) is the linear velocity of the inner gear tooth tip, \(u_{12}\) is the linear speed of the internal gear indexing circle, \(R_{z2}\) is the radius of the internal gear shaft, \(\theta_{2}\) is the included angle of the inner gear root.

Set the flow into and out of the transition zone as \(q_{in}\) and \(q_{out}\) , the starting point of the time when the entire tooth concave completely enters the transition zone is \({ }t = 0\) , and the internal gear angle \({\uptheta } = {\upomega }_{2} {\text{t}}\) , where \({\upomega }_{2}\) is the internal gear speed, and the pressure change in the transition zone within \({\text{dt}}\) time is \(dp_{2}\) . From the continuity equation of compressible fluids, then27

In the equation: \(K_{e}\) is the volume elastic modulus of hydraulic oil, \(V_{2}\) is the volume of oil in the tooth cavity.

Substitute \({\text{q}}_{1}\), \({\text{q}}_{2}\), \({\text{q}}_{3}\), \({\text{q}}_{4}\) and \({\text{q}}_{5}\) into Eq. (6),

Due to the fixed volume of the tooth concave, \(\frac{{dV_{2} }}{dt} = 0\). When the internal gear speed is \({\text{n}}_{2}\) , \(\frac{{dp_{2} }}{{{\text{d}}t}} = 2\uppi n_{2} \frac{{dp_{2} }}{{{\text{d}}\upvarphi _{2} }}\) , then the non-linear differential equation of the pressure in the tooth concave area can be sorted out to obtain,

Set, \(A_{1} = \frac{{K_{e} }}{{2{\pi n}_{2} V_{2} }}\), \(A_{2} = \frac{{bh_{2i}^{3} }}{{12\mu {\text{s}}_{e2} }}\), \(A_{3} = \frac{{R_{e2} - R_{i2} }}{{6\mu {\text{s}}_{2} }}h_{2f}^{3}\),\(A_{4} = \frac{{\theta h_{2f}^{3} }}{{6\mu ln\frac{{R_{i} }}{{R_{z2} }}}}\).

Then, Eq. (8) can be simplified as

The Eq. (9) is the differential equation for the pressure change in the tooth concave area, and its initial conditions are:\(\uptheta = 0\), \(p_{2} = p_{g}\).

As shown in Fig. 2, the included angle of a tooth concave on the tooth top circle is \(\theta^{\prime}\), and the included angle of a gear tooth on the tooth top circle is \({\uptheta ^{\prime\prime}}\). The included angle of the outer lunar pressure block is \(\theta_{1} + \theta_{2}\), the included angle of the tooth concave area is \(\theta_{1}\), and the included angle of the high-pressure area is \(\theta_{2}\). The sum of \(\theta^{\prime}\) and \({\uptheta ^{\prime\prime}}\) is \(\alpha\), \(\alpha = \frac{2\pi }{z}\), \(z\) is the number of teeth. The change period of pressure \(p\left( \theta \right)\) in the transition zone is \(\alpha\). The change in pressure \(p\left( \theta \right)\) is shown in Fig. 3.

Pressure distribution in the transition zone: (A) Starting position, \({\uptheta } = 0\)°. (B) Gear rotation angle \({\uptheta }\left( {0 < {\uptheta } < \theta^{\prime} - {{\uptheta^{\prime\prime}}}} \right)\); (C) Gear rotation angle \({\uptheta } = \theta^{\prime} - {{\uptheta^{\prime\prime}}}\); (D) Gear rotation angle \({{\uptheta }}\left( {\theta ^{\prime} - {{\uptheta ^{\prime\prime}}} < {{\uptheta }} < {{\uptheta ^{\prime}}}} \right)\); (E) Gear rotation angle \({\uptheta } = {{\uptheta^{\prime}}}\); (F) Gear rotation angle \({\uptheta }\left( {\theta^{\prime} < {\uptheta } < \theta^{\prime} + {{\uptheta^{\prime\prime}}}} \right)\); (G) Gear rotation angle \({\uptheta } = \theta^{\prime} + {{\uptheta^{\prime\prime}}}\).

The initial position is the line connecting the endpoint of oil groove 11 and the center of circle O2, where point C of the tooth groove just passes through. The process of point C rotating angle \({\uptheta }\left( {0 < {\uptheta } < \theta^{\prime} - {{\uptheta^{\prime\prime}}}} \right)\).At this point, the tooth concave in the figure is in communication with the high-pressure chamber, and the distribution of \(p\left( \theta \right)\) is,

\({\upbeta }\) is the angle between the line connecting any point in the region and point O2 and the x-axis. The process of tooth concave point C rotating angle \({\uptheta }\left( {\theta^{\prime} - {{\uptheta^{\prime\prime}}} < {\uptheta } < {{\uptheta ^{\prime}}}} \right)\), and the distribution of \(p\left( \theta \right)\) is,

The process of tooth concave point C rotating angle \({{\uptheta }}\left( {\theta ^{\prime} - {{\uptheta ^{\prime\prime}}} < {{\uptheta }} < {{\uptheta '}}} \right)\), and the distribution of \(p\left( \theta \right)\) is,

The force analysis of the outer crescent block as the research object is shown in Fig. 4. The FH section is subjected to pressure in the transition zone, and the direction of the force always points towards the center of the circle \({{\text{o}}}_{2}\); the HQ section is subjected to high-pressure hydraulic pressure, and its direction is always perpendicular to the HQ section; high pressure oil is introduced into the oil chamber of Zone I of the QL section, pushing the crescent block radially outward, and the direction of force always points towards the center of the circle \({{\text{o}}}_{2}\); the EF section is subjected to a reaction force from the stop pin, and the direction of the force is always perpendicular to the pressure boundary line; Zones II and III are low-pressure zones, with point K subjected to the elastic force \({{\text{F}}}_{N1}\) of the rectangular compression spring 4 at the center of the circle; Point L and point M are subjected to the elastic force perpendicular to the baffle spring;the top circle radius of the inner gear is \({{\text{r}}}_{o2}\), the top circle radius of the outer gear is \({{\text{r}}}_{o1}\), the gear thickness is \({\text{b}}\), and the radial thickness of the outer crescent block is d, the theoretical clearance between the inner and outer crescent blocks is \(\Delta\), the position angle of the baffle spring are \(\upvarepsilon\), \(\updelta\); the angle between the pressure boundary line and the X-axis is \({\alpha }_{0}\), the center angle between the second sealing rod and the pressure boundary line is \({\alpha }_{1}\), the center angle between the first sealing rod and the second sealing rod is \({\alpha }_{2}\), the center angle between the first baffle spring and the first sealing rod is \({\alpha }_{3}\).

Hydrodynamic model of the outer crescent block.

Segmental analysis:

FH segment:

The change in pressure in the transition zone within a cycle.

\({\text{H}}^{\prime } {\text{J}}\)\({\text{HQ}}\) segment:

\({\text{EF}}\) segment:

The elastic force of the rectangular compression spring is \(F_{N1}\):

The spring force of the first baffle is \(F_{N2}\):

The spring of the second baffle is \(F_{N3}\):

So, the combined external thrust force on the outer crescent block can be expressed as the following equation,

The force analysis of the inner crescent block as the research object is shown in Fig. 5. The angle range of the internal crescent block is \({\theta }_{3}+{\theta }_{4}\), the included angle of the tooth concave area is \({\theta }_{3}\), and the included angle of the high-pressure area is \({\theta }_{4}\).The PT section is subjected to pressure in the transition zone, and the direction of the force always points towards the center of the circle \({{\text{o}}}_{1}\); The ST segment is subjected to the support reaction force \({F}_{ST}\) of the stop pin, and the direction of the force is always perpendicular to the pressure boundary line; The JP section is subjected to high-pressure hydraulic pressure \({F}_{JP}\) , with a direction perpendicular to the JP section; The IJ section is subjected to high-pressure hydraulic pressure \({F}_{IJ}\) and points towards the center of the circle \({{\text{o}}}_{2}\); The NI section is subjected to hydraulic pressure \({F}_{NI}\) and its direction is perpendicular to the NI section; The sizes of \({F}_{N1}\), \({F}_{N2}\) and \({F}_{N3}\) are the same as those of the external crescent, but the direction of force is opposite.

Mechanical model of the inner crescent block: (A) Geometric and hydrodynamic models of the tooth recess; (B) A hydrodynamic model of the inner crescent block.

\({\text{PT}}\) segment:

The flow into and out of the tooth concave area are respectively \(q_{6}\),\(q_{7}\), \(q_{8}\),\(q_{9}\) and \(q_{10}\). Calculate the pressure in the concave area of the tooth according to the calculation method of the outer crescent, and similarly calculate the force \(F_{PTx}\),\(F_{PTy}\).

\({\text{ST}}\) segment:

\(F_{ST}\) is the reaction force of the pin support.

\({\text{JP}}\) segment:

Applying the sine theorem in \(\Delta O_{1} O_{2} P\)

So, \({\text{JP}} = r_{o2} - O_{2} P\), therefore

\({\text{IJ}}\) segment:

\({\text{NI}}\) segment:

So, the combined external thrust force on the inner crescent block can be expressed as follows:

When the gear pump is working, in order to reduce radial leakage, it is necessary to ensure that the inner and outer crescent blocks always fit the tooth top circle, and to prevent excessive jamming between the crescent blocks and the gear, the outer surface of the crescent and the gear must have lubrication properties28,29,30. Therefore, the pressure of the compensation chamber cannot be designed too small or too large. Therefore, it is necessary to reasonably design the angle \(\mathrm{\alpha^{\prime}}({\mathrm{\alpha ^{\prime}}}={\alpha }_{3}+{\alpha }_{4})\) of the QL section of the compensation chamber formed by the inner and outer crescent blocks in the compensation device.

The compensation forces in the QL are equal in magnitude and opposite in direction, and in the design of high-pressure gear pumps, the forces \({F}_{N1}\),\({F}_{N2}\) and \({F}_{N3}\) are much smaller than the hydraulic pressure in the transition zone31,32,33. Therefore, when establishing constraint programming, the sizes of \({F}_{N1}\),\({F}_{N2}\) and \({F}_{N3}\) can be ignored to obtain \({F}_{EF}\) and \({F}_{ST}\).

During normal operation of the gear pump, the inner and outer EF and ST sections always adhere to the stop pins, ensuring that \({F}_{EF}\ge 0\) and \({F}_{ST}\ge 0\) are met.

Substitute its value into Eqs. (19) and (24) to obtain the X and Y components when the inner and outer lunar blocks rotate.

Calculate the average value \(\overline{{F}_{WX}}\), \(\overline{{F}_{WY}}\),\(\overline{{F}_{NX}}\) and \(\overline{{F}_{NY}}\) for each cycle.

Calculate the external thrust \(F_{W} = \sqrt {\left( {\overline{{F_{WX} }} } \right)^{2} + \left( {\overline{{F_{WY} }} } \right)^{2} }\) and \(F_{N} = \sqrt {\left( {\overline{{F_{{NX}} }} } \right)^{2} + \left( {\overline{{F_{{NY}} }} } \right)^{2} }\) of the inner and outer crescent blocks.

The established objective function is:

The material of the inner and outer Crescent blocks is beryllium bronze, and its processing technology conditions refer to FED-STD-00153, Copper Base Alloy Casting, Chimical Combustion And Mechanial Properties issued on June 30, 1967.The material of the sealing rod is tetrafluoroethylene filled with 25% graphite, and its technical requirements and test methods refer to ISO23529, Rubber-General Process For Preparing And Condioning Test Pieces For Physical Test Methods, issued on October 15, 2010.The gear material is 20GrMnTi, and its mechanical properties meet the requirements of ISO4990, Steel Castings-General Technical Requirements, issued on November 1, 2003. The test method referred to the Rotodynamic Pumps Hydraulic Performance Acceptance Tests, ANSI/HI 14.6-2011, issued in 2011. Then, the testing process also referred to ISO9906, Rotodynamic Pumps-Hydraulic Performance Access Test -Grades 1 And 2, issued on May 1, 2012. The test bench is shown in Fig. 7E.

Taking the IPFY series internal meshing gear pump developed by the Hydraulic Parts Factory of Fuzhou University as the object (as shown in Fig. 6), with a theoretical displacement of 100.5 ml/r and a rated pressure of 20 MPa, experimental research was conducted. The design parameters : gear modulus \({\text{m}} = 3\), external tooth number \(z_{1} = 13\), internal tooth number \(z_{2} = 9\), pressure angle of 20°, tooth width thickness \({\text{b}} = 41\) mm, external gear modification coefficient \(\xi_{1} = 0.432\), internal gear gear modification coefficient \(\xi_{2} = 0.553\), gear pair center distance \({\text{e}} = 9.253\) mm, tooth top height coefficient \(h_{a}^{*} = 1\) mm, top clearance coefficient \(c^{*} = 0.25\) mm, external crescent tooth thickness \({\text{d}} = 2.6\) mm, initial clearance of internal and external crescent blocks \(\Delta = 0.3\) mm, initial angle of pressure boundary 0°, top circle radius of internal teeth \(r_{o1} = 23.8\) mm, the radius of the top circle of the outer gear tooth is \(r_{o2} = 27.15\) mm, the center angle of the outer gear tooth groove on the top circle is \(\theta_{1}^{\prime} = 25^\circ\), the center angle of the outer gear tooth groove on the top circle is \(\theta^{\prime\prime}_{1} = 2.7^\circ\), the center angle of the inner gear tooth groove on the top circle is \(\theta_{2}^{\prime} = 13.8^\circ\), the center angle of the inner gear tooth groove on the top circle is \(\theta^{\prime\prime}_{2} = 5.1^\circ\), the center angle of the outer crescent boundary arc length is \(\alpha_{1} + \alpha_{2} + \alpha_{3} + \alpha_{4} = 75.6^\circ\), and the center angle of the inner crescent boundary arc length is \(\theta_{3} + \theta_{4} = 83.1^\circ\), The installation angle of the first and second baffle springs is \({\upvarepsilon } = 30.9\), \({\updelta } = 18.4\), taking \(F_{N1} = F_{N2} = F_{N3} = 250 N\) and \(\alpha_{1} = \alpha_{2}\),\(\alpha_{3} = \alpha_{4}\) respectively. Use MATLAB programming to calculate the magnitude of the external and internal thrust \(F_{W}\) and \(F_{N}\) of the inner and outer crescent blocks when rotating through a tooth slot and a gear tooth. Constrained optimization of the objective function was performed using the optimization tool fminbnd, and \(\alpha^{\prime} = 31.23^\circ\) was obtained through analysis. \(F_{c}\) is the compensating force. The Fig. 7A,B shows that during the process of gear rotation, the force on the crescent block shows a sudden and abrupt change. The variation of \(F_{FH}\) with rotation angle is consistent with reference34. The variation of \(F_{PT}\) with rotation angle is consistent with reference35. The size of the compensation force \(F_{{\text{C}}}\) is similar to the force \(F_{w}\) and \(F_{N}\) on the crescent block, which is consistent with the conclusion drawn in reference36.

Support reaction model of the steering pin.

Experimental study of an internal gear pump: (A) The force variation curve of the external crescent block. (B) The force variation curve of the internal crescent block; (C) Volume efficiency curve with pressure; (D) Curve of flow changing with speed; (E) Bench testing; (F) Disassembled part diagram.

Under the environmental conditions of using L-HM46 hydraulic oil, with an inlet pressure of 0.13 MPa and an outlet pressure of 20.5 MPa, a test oil temperature of \(50\pm 4\mathrm{^\circ{\rm C} }\), and a rated speed of 1800 RPM. The volumetric efficiency reached 94.6%, and there were no abnormal wear marks on the surface of the inner and outer crescent blocks. The parts are shown in Fig. 7F.

The experiment set up a control group. The gear pump in control group 2 adopts a fixed crescent plate structure, with an axial and radial clearance of 0.2 mm. Pump 1 and pump 2 have the same theoretical displacement. Figure 7C shows that gear pumps with compensated crescent plates have higher volumetric efficiency under high pressure; Fig. 7D shows that as the speed changes, pump 1 has a higher flow output.

Based on the actual working conditions of the tooth groove and gear teeth, this paper establishes a geometric model of the radial compensation device for the internal meshing gear pump. By adopting the technical measure of reducing the sealing area of the crescent block to a tooth concave area, a fluid dynamics model of the crescent block was established, and the pressure variation with gear rotation in the transition zone was derived. Then, establish a design model to obtain the optimization angle of the compensation mechanism. These works can provide reference for the design and optimization of high-pressure internal meshing gear pumps, and also contribute to a deeper understanding of the lubrication characteristics of compensation mechanisms.

Taking the radial compensation device of the high-pressure internal meshing gear pump as the research object, the force analysis of the inner and outer crescent blocks was carried out. A design model was established during the gear rotation cycle, and based on this, fminbnd constraint optimization was carried out to obtain the compensation chamber angle, as well as the angle positions of the baffle spring, sealing rod, and rectangular compression spring.

Draw the curve of the hydraulic external thrust of the inner and outer crescent blocks as a function of the rotation angle. When passing through a tooth groove, the external thrust increases linearly, while when passing through a tooth, the external thrust decreases linearly.

Experimental research shows that the internal meshing gear has an output efficiency of 94.6% at an output pressure of 20.5 MPa, a speed of 1800 RPM, and a compensation chamber angle of \({\alpha }^{\prime}=31.23^\circ\). It operates normally without any phenomenon of jamming or locking. The feasibility and correctness of the model have been verified through practical examples.

Due to the wide scope of modeling work, parameter variables such as material forming, machining errors, assembly tolerances, and cold and hot deformation of each material were not considered. The energy loss of the transmission medium in the circuit has not been considered. The research topic still has further research value. In the future, considering multiple factors, the accuracy of design models can continue to be improved. Verify the model by testing the outlet pressure of the pump and the leakage of the friction pair. Further increase the operating pressure of the internal meshing gear pump.

The datasets used and/or analysed during the current study are available from the corresponding author on reasonable request.

Bae, J. H. & Kim, C. Design of rotor profile of internal gear pump for improving fuel efficiency. Int. J. Precis. Eng. Manuf. 16, 113–120 (2015).

Article Google Scholar

Chai, H., Yang, G., Wu, G., Bai, G. & Li, W. Research on flow characteristics of straight line conjugate internal meshing gear pump. Processes 8, 1–28 (2020).

Article Google Scholar

Choi, T. H. et al. Design of rotor for internal gear pump using cycloid and circular-arc curves. J. Mech. Des. 134, 1–12 (2012).

Article Google Scholar

Cui, G., Liu, Z., Xian Ma, S. & Cheng, Z. Dynamic characteristics of carbonate saline soil under freeze–thaw cycles in the seaonal frozen soil region. Alex. Eng. J. 81, 384–394 (2023).

Article Google Scholar

Du, R., Chen, Y. & Zhou, H. Numerical analysis of the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps. Proc. Inst. Mech Eng. Part C J. Mech. Eng. Sci. 232, 2297–2314 (2018).

Article Google Scholar

Du, R., Chen, Y. & Zhou, H. Investigation into the lubricating gap between the ring gear and the case in internal gear pumps. Ind. Lubr. Tribol. 70, 454–462 (2018).

Article Google Scholar

Ferrari, A., Fresia, P., Rundo, M., Vento, O. & Pizzo, P. Experimental measurement and numerical validation of the flow ripple in internal gear pumps. Energies 15, 9607 (2022).

Article CAS Google Scholar

Guo, J., Zhong, J., Li, Y., Du, B. & Guo, S. A hybrid artificial fish swam algorithm for disassembly sequence planning considering setup time. Assem. Autom. 39, 140–153 (2019).

Article Google Scholar

Guo, S. & Chen, D. Calculation of unloading area of internal gear pump and optimization. Math. Probl. Eng. 2020, 1–9 (2020).

MathSciNet Google Scholar

Hoa, P. T. Analysis of effect of oil viscosity and temperature on dynamic pressure distribution in internal gear motor and pump. Springer Proc. Mater. 6, 245–253 (2020).

Article Google Scholar

Ivanović, L. T., Velicković, S. N., Stojanović, B., Kandeva, M. & Jakimovska, K. The selection of optimal parameters of gerotor pump by application of factorial experimental design. FME Trans. 45, 159–164 (2017).

Article Google Scholar

Vasić, M., Blagojević, M., Stojić, B. & Dizdar, S. Design and performance analysis of an in-wheel hub reducer. Adv. Eng. Lett. 1, 115–125 (2022).

Article Google Scholar

Blagojevic, M., Marjanovic, N., Djordjevic, Z., Stojanovic, B. & Marjanovic, V. Numerical and experimental analysis of the cycloid disc stress state. Teh. Vjesn. 21, 377 (2014).

Google Scholar

Chernets, M., Shil’ko, S. & Kornienko, A. Calculated assessment of contact strength, wear and resource of metal-polymer gears made of dispersion—Reinforced composites. Appl. Eng. Lett. 6, 54–61 (2021).

Article Google Scholar

Liang, Y., Chen, Z. & Liao, J. Numerical simulation and experimental evaluation of flow ripple characteristics of Truninger pump. Sci. Rep. 12, 1–29 (2022).

Article ADS Google Scholar

Liao, J., Zheng, J. & Chen, Z. Research on the fault diagnosis method of an internal gear pump based on a convolutional auto-encoder and PSO-LSSVM. Sensors 22, 9841 (2022).

Article ADS PubMed PubMed Central Google Scholar

Liu, Y. Y., An, K., Liu, H., Gong, J. G. & Wang, L. Q. Numerical and experimental studies on flow performances and hydraulic radial forces of an internal gear pump with a high pressure. Eng. Appl. Comput. Fluid Mech. 13, 1130–1143 (2019).

Google Scholar

Lobsinger, T., Hieronymus, T., Schwarze, H. & Brenner, G. A CFD-based comparison of different positive displacement pumps for application in future automatic transmission systems. Energies 14, 2501 (2021).

Article Google Scholar

Mo, J., Gu, C., Pan, X., Zheng, S. & Ying, G. Experimental and numerical study of the influence of loading direction on the lubrication and cooling of self-circulating oil bearing system applied in internal gear pumps. Proc. Inst Mech. Eng. Part J J. Eng. Tribol. 232, 415–426 (2018).

Article Google Scholar

Osiński, P. et al. Development tendencies of clearance compensation methods in internal gear pumps. MATEC Web Conf. 338, 01021 (2021).

Article Google Scholar

Osiński, P. & Warzyńska, U. FEM strength analysis of circumferential compensation with integrated lips in gear pumps. Energies 15, 2691 (2022).

Article Google Scholar

Pan, D. & Vacca, A. Modeling of crescent-type internal gear pumps considering gear radial micromotion. Chem. Eng. Technol. 46, 128–136 (2023).

Article CAS Google Scholar

Peng, Z., Liejiang, W., Rongmin, L., Mingyuan, L. & Yan, Q. Flow field modeling and simulation of high-speed gear pump considering optimal radial and end clearance. IEEE Access 11, 64725–64737 (2023).

Article Google Scholar

Stanojević, M., Tomović, R., Ivanović, L. & Stojanović, B. Critical analysis of design of ravigneaux planetary gear trains. Appl. Eng. Lett. 7, 32–44 (2022).

Article Google Scholar

Ivanović, L., Stojanović, B., Blagojević, J., Bogdanović, G. & Marinković, A. Analysis of the flow rate and the volumetric efficiency of the trochoidal pump by application of Taguchi method. Teh. Vjesn. Tech. Gaz. 24, 265–270 (2017).

Google Scholar

Li, G., Zhang, L. & Han, W. Profile design and displacement analysis of the low pulsating gear pump. Adv. Mech. Eng. 10, 1–11 (2018).

Google Scholar

Torrent, M., Gamez-Montero, P. J. & Codina, E. Motion modelling of the floating bushing in an external gear pump using dimensional analysis. Actuators 12, 338 (2023).

Article Google Scholar

Pham, T. H., Nguyen, D. T. & Weber, J. Theoretical, simulation and experimental investigation of 1D hybrid pressure distribution for internal gear motors and pumps. J. Mech. Sci. Technol. 34, 97–108 (2020).

Article Google Scholar

Chai, H., Yang, G., Wu, G., Bai, G. & Cao, C. Analysis of straight conjugate internal gear pump through numerical modeling and experimental validation. PLoS ONE 17, e0270979 (2022).

Article CAS PubMed PubMed Central Google Scholar

Pietrzyk, T., Georgi, M., Schlittmeier, S. & Schmitz, K. Psychoacoustic evaluation of hydraulic pumps. Sustainability 13, 1–22 (2021).

Article Google Scholar

Rituraj, R. & Vacca, A. Investigation of flow through curved constrictions for leakage flow modelling in hydraulic gear pumps. Mech. Syst. Signal Process. 153, 107503 (2021).

Article Google Scholar

Shen, H., Li, Z., Qi, L. & Qiao, L. A method for gear fatigue life prediction considering the internal flow field of the gear pump. Mech. Syst. Signal Process. 99, 921–929 (2018).

Article ADS Google Scholar

Gao, L., Hu, X., Liu, W. & Sun, D. Study on wear mechanism of gear pump end plate of combined harvester based on CFD fluid analysis. Concurr. Comput. Pract. Exp. 31, 1–18 (2019).

Article Google Scholar

Tessari, F., Galluzzi, R. & Amati, N. Efficiency-driven design methodology of gerotor hydraulic units. J. Mech. Des. 142, 063501 (2020).

Article Google Scholar

Xu, B., Hu, M., Zhang, J. H. & Mao, Z. B. Distribution characteristics and impact on pump’s efficiency of hydro-mechanical losses of axial piston pump over wide operating ranges. J. Cent. South Univ. 24, 609–624 (2017).

Article Google Scholar

Yamamoto, M., Hosogi, T., Watanabe, T. & Nishida, Y. Development of engine lubrication system with new internal gear fully variable discharge oil pump. SAE Int. J. Fuels Lubr. 10, 904–912 (2017).

Article Google Scholar

Download references

The writers are grateful for the financial support from the Fujian Provincial Education Science Planning Project Fund (FJJKBK21-031).

College of Electronics and Information Science, Fujian Jiangxia University, Fuzhou, 350108, China

Shanxin Guo

Fuzhou University Hydraulic Component Factory, Fuzhou University, Fuzhou, 350002, China

Guangchi Yu

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

S.G. and G.Y designed this study. G.Y. collected the data, S.G. analyzed the data. All authors contributed to the article and approved the submission version.

Correspondence to Shanxin Guo.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and permissions

Guo, S., Yu, G. Research and design of internal meshing gear pump separating crescent plate. Sci Rep 14, 3519 (2024). https://doi.org/10.1038/s41598-024-53892-6

Download citation

Received: 18 October 2023

Accepted: 06 February 2024

Published: 12 February 2024

DOI: https://doi.org/10.1038/s41598-024-53892-6

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

Journal of Engineering and Applied Science (2024)